Aircraft Spruce & Specialty Co.
Contact Us
Call Us
Sign In
- Photo may represent series and not specific product
- SHARE
Pressure Fuel Cap 2
MFR Model# 0483347
FREE Shipping
- JUMP TO
- Overview
- Accessories
- Reviews
- Q&A
- View in Catalog
Overview
|
NOTE: Not intended for aerospace use. Commercial product use only. no FAA Approval. These caps are made with Buna-Nitrile gaskets for fuel resistance. These caps are non-vented for gravity fuel systems. The dimension referenced on these pressure fuel caps is the OD of the rubber grommet around the neck (base). |
 |
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. |
Reviews
Perfect fit, great product!
Verified Purchase
Pressure Fuel Cap 2
Good quality and fits well. Exactly the same item as, if you buy it from Aviat for Pitts.
Verified Purchase
Pressure Fuel Cap 2
Not FAA/PMA approved. Good for use on a homebuilt with some modification
Verified Purchase
Pressure Fuel Cap 2
Worked as it should.
Verified Purchase
Pressure Fuel Cap 2
This product is unusable for my application. The fuel cap will not fit securely. The diameter is correct but the cap spins in the fuel tank opening. Tightening the cap only squeezes it out of the opening despite the zero-taper filler neck.
Verified Purchase
Pressure Fuel Cap 2
I purchased these fuel caps to replace the stock fuel caps on the main fuel tanks on a 1960 Beech Debonair. Ive not yet permanently installed them, but, as is, they look like they will work well with three exceptions. Id like the caps to fit a bit tighter when the locking lever is pushed down in order to tighten them in the fuel tank opening, I need to add a thin washer under the cam that is part of the locking lever - to do this, Ill need to drill out the permanently installed pin on which the locking lever rotates and replace it with a clevis pin as was done on the stock fuel caps. In addition, highest portion (when installed in the plane) of the locking lever will need to be ground off as it conflicts with the fuel tank door that covers the fuel cap. In addition, there is no provision on the bottom of the cap to attach the chain that is attached to the fuel cap keeper that helps keep you from losing your fuel cap while fueling. I may do all of this or, in the alternative, I may remove the rubber portion from the new fuel cap, cut off the bottom of that rubber piece so it is the same length as the rubber portion on the stock cap, and then install the new rubber portion on my stock cap. Of course, whether I use the new cap, or use the rubber from the new cap to repair my stock cap, the metal portion of the cap (other than the locking lever) needs to be painted bright red as was done by Beech. Ive seen replacement rubber pieces for sale for $400 - $500 a piece so, in either event, these new fuel caps will provide a good solution to the loose fitting rock hard rubber portions of the stock caps on this aircraft.
Got these just for the rubber parts, which worked perfectly on my Siai-Marchetti SF 260 fuel caps. Its too bad they dont sell only the rubber because I just threw the metal pieces away.
Bought this to replace the last one which was 20 years old. Wish they just sold the insert, but it does whats on the tin.
The rubber should be sold separately. It doesnt last forever and its a real waste to have to buy an entire cap.
Verified Purchase
Pressure Fuel Cap 2
the snap tops are to tall. wont fit mooney M20C. wing fuel cap covers cant close.
Q&A
Please note, Aircraft Spruce's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.
The dimension referenced on these pressure fuel caps is the OD of the rubber grommet around the neck (base).
The measurement is the estimated grommet O.D., so the measurement listed would be the I.D. of the neck it would be used on.
Approx 11/16
