The stuff worked great. Its premixed and all you have to do is stir it well. After prepping the area, brush it on and bam, new wing walk!!!

David L Verified Purchase

Ultra Wing Walk

Product was just what I needed. However, was nearly impossible to remove can lid. Wrecked it trying to get it off.

Andy S Verified Purchase

Ultra Wing Walk

Amazing product. Love it. Its better than the original coating that feels more like a sand paper. I used this to repaint the wing walk on mu Grumman Cheetah. Minimal prep required. Do stir well and follow instructions. I did not take off the previous coat. It peeling at places. This is rubberized and has a nicer grip and feel, just like a shoe sole! The grippy grit is also even sized rubber bits. I used a foam roller and it went pretty well. Just mask with painters tape and roll on the paint. Easy to level places that were missing paint. Dried within 2-3 hours. Tested it next day and it was well cured.

Gagan S Verified Purchase

Ultra Wing Walk

Excellent

Vern S Verified Purchase

Ultra Wing Walk

I am very happy with the Ultra Wing walk paint I applied to my Ercoupe, really looks nice.

Paul B Verified Purchase

Ultra Wing Walk

This is a very course grained product. Suitable for flat as opposed to rounded surfaces.

Brian E Verified Purchase

Ultra Wing Walk

This stuff works great. Spend a little time on prep work, follow directions, and it works great. I used a paint mixer on my cordless drill, scrubbed the area with soap and water (wire brush on bare metal spots) masked it off, and painted it on with a brush. Looks great. *****

Richard A Verified Purchase

Ultra Wing Walk

This product is an excellent product, easy to use, excellent grip and durable if you take your time and properly prepare the underlying surface. Patience is they key. Patience opening and closing the can. Proper stirring. And patience letting it dry fully, which may take a bit longer than indicated in high humidity environments. Be patient, prep properly and you’ll have a great looking, functional finish.

Curtis L Verified Purchase

Ultra Wing Walk

Fantastic product! Take your time, clean and prep the surface, apply the material evenly, and you’ll be quite pleased with the result. We did not remove the old wing walk. We used a roller to apply the product and applied two coats. The result looks like new. Tough, and slip resistant. Will use it again!

Mark S Verified Purchase

Ultra Wing Walk

This stuff is great! We used a single 1 Qt can to re-furb the wing walks on a pair of low wing singles. The can is almost impossible to open (there must be a trick, I resorted to turning it upside down and using a can opener) and you need an assistant to keep stirring it constantly, but it goes on well, does not run, and the little chunks are VERY even. It dries with a beautiful liquid sheen and is very secure under foot when dry, a little slippery with wet shoes. But speaking of water, water sheets off it like magic and it is easy to clean. Im super happy with the product.

I bought this to redo the wing walks of my Grumman AA1-A and it worked beautifully. The wing walks now look pretty much like new. It was very simple to apply as well.

Douglas P Verified Purchase

Ultra Wing Walk

Great wing walk. Easy to apply and durable.

Easy to apply, drys to a smoother texture then other wing walk. Good stuff👍

Goes on easy with a brush. Fair warning, mask off areas very well and pay special attention to any joints that need to remain accessible (access panels). This stuff sticks and will get everywhere. Very good working time and easy to stir with a screwdriver. Used only about 1/2 on a Debonair.

Works as advertised

Takes a bit longer to dry. Say 48 hours.

Really quick shipping

Great DIY product. Just prep the surface, mask the perimeter, stir well, and apply with a roller. Finish is super tough, rough, and glass black.

We are painting a team of T6s and used this on the first one. I was impressed enough to order enough to do the next three.

Good product brings the wing walk back to life. Make sxure you stir all during the application

Plan on 24 hours for complete curing.

Bought this for my Grumman AA5A. This stuff is messy like everyone said. I bought a roller and pan. Put on two coats and it took the quart. It looks good. I gave it a 4 because of the messiness and after two coats it still had a some white spots in it.

This product is a can of Herculiner, truck bed coating with a sticker over the top. Save yourself fifteen dollars and just go to your local auto parts store.

It was very hard to open and was damaged in the process.

Saleh Verified Purchase

Ultra Wing Walk