SAME DAY SHIPPING ON ORDERS PLACED BY 4 PM | 877-4-SPRUCE

Swift Oil Pressure Sensors 100 Psi

$73.80/Each
Quantity
Add to Wishlist
Part# 10-04057
MFR Model# SP-100PV

Overview

Swift Pressure Sensors / transducers are designed and manufactured using the most advanced technologies. They have been used in many different industries. This pressure sensor / transducer works with a variety of media, i.e. oil, air, water, etc. Unlike the resistance type sender, this is a solid state transducer with no moving parts which does not allow for any opportunity for the sender to become worn out mechanically.

Similar to Falcon Gauge
Made in China
   
California Prop 65 Warning Symbol

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Specifications

  • Output: 0.5-4.5 Volt
  • Operation Temperature: -40~125 Degree C
  • Life: 1,000,000 Time
  • Weight: 40g
  • Accuracy: 0.5%
  • Thread: 1/8" NPT
  • PSI: 100
  • Frequently Purchased With
  • Customers Also Viewed
  • Related Items

Reviews

Just got it installed on my Jabiru 3300, and went for a short flight. Iit seems to be working well. I connected it to my GRT EIS6000 with a scaling factor of 61, and an offset of 19 (which means -10). I like the fact that the housing and transducer return line are isolated, preventing a ground loop through the engine ground. If I have problems later on, Ill update this review if possible. I gave it 4 stars instead of 5 because the plastic retaining latch on the connector broke off the first time I plugged it in. Id recommend getting the plastic warm before trying to plug in the connector because it seems very brittle. I left Aircraft Spruce an order feedback comment about this, but havent heard anything. I ended up drilling a couple small holes in the remaining portion of the plastic latch, and threaded safety wire through it, and around the receptacle housing. Its a band-aid solution, but its solid, and I dont have to worry about the connector coming unplugged.

Paul L
January 25, 2021

Q&A

Please note, Aircraft Spruce's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

Q: Would the Falcon 100PSI Oil Pressure Sender sensor turn on a light when there is no oil pressure?

This sender has three wires for power, ground and connection to a gauge and does not have a warning indication line.

Q: Can I use the Falcon Oil Pressure Sensor 100 PSI sensor for a Rotax 912?

Rotax changed their oil pump housings in last few years. If yours is newer type, then this will seem to fit but cause leaks and strip the threading. This will work fine if you have the older style 1/8" threading type.

Q: Can I replace a 100psi VDO sender with a falcon sender?

We do not recommend using VDO gauge with a falcon sender.

Q: Will this sender work with the WESTACH OIL PRESSURE GAUGE K2A8MM?

No cross reference data is available at this time. Westach recommends using only the sender included with the K2A8MM. The PN of the standalone Westach sender is 10-02640.

Q: I assume the wiring harness pictured is included with the sensor? How long is the wiring harness?

Yes, it is included. The length is approximately 42 inches.

Q: What color wire is ground, power, and signal to the instrument?

Per the manufacturer, black is ground, yellow is the sender signal and red is 5 VDC.

Q: Is this Swift sensor FAA TSOd?

No. This product does not have FAA Approval. It is intended for use in experimental aircraft only.

Q: Is this sensor compatible with the Dynon Flightdeck 180?

Dynon recommends using only Dynon sensors in the Flightdek 180.

Q: What is the supply voltage? Do you have a data sheet?

Per the manufacturer, output voltage is 0.5-4.5 volts.

Q: Does this sensor come with the lead shown in the online photograph?

Yes, this product comes as shown in the photo.

View in Catalog

View Image View in Catalog