THE AVIATION SUPERSTORE FOR ALL YOUR AIRCRAFT & PILOT NEEDS | 877-4-SPRUCE
Thumbs 1
Thumbs 1
Thumbs 1
Thumbs 1
Thumbs 1
Thumbs 1

West System Epoxy Kits

From $77.00 to $617.00
Kit
No.
Kit Size PN #105
Resin
#205-Fast #206-Slow Kit Price Buy
A-11.2 Qt.
01-08100
32 oz.7 oz.-----$79.95
Quantity
A-21.2 Qt.
01-08200
32 oz.-----7 oz.$77.00
Quantity
B-11.2 gal
01-08300
126 oz.27 oz.-----$182.95
Quantity
B-21.2 gal
01-08400
126 oz.-----27 oz.$176.95
Quantity
C-15.25 gal
01-08500
4.35 gal121 oz.-----$617.00
Quantity
C-25.25 gal
01-08600
4.35 gal-----121 oz.$586.00
Quantity
Subtotal $0.00
Add to Wishlist

Overview

WEST SYSTEM brand resins and hardeners, form a two-part epoxy system developed by Gougeon Brothers specifically for wood and composite boat construction. Rutan Aircraft Factory now recommends WEST SYSTEM epoxy for certain homebuilt aircraft applications, particularly where a moisture resistant epoxy is desired. 105 Resin is the base material on which all of the WEST SYSTEM epoxy systems are built. The resin is a clear, light amber, low-viscosity liquid. It is designed specifically to wet out wood fiber. With roller applications, it possesses excellent thin film characteristics in flowing out and is self-leveling without fish-eyeing. Its relatively high flash point makes it safer to work with than polyesters. It can be cured in a wide temperature range, then sanded and shaped. It cures quite clear so that the natural finish shines through.

205 Fast Hardener, when mixed with the 105 Resin in a ratio of 5 parts Resin to 1 part Hardener, yields a high-strength, rigid solid with excellent cohesive properties and provides an excellent moisture vapor barrier. The 105 Resin/205 Fast Hardener has a pot life of 10-15 minutes at 70°F. It is also recommended in coating applications where natural finishing is desired. Partial cure time at 70°F is 5-7 hours. 206 Slow Hardener is a low-viscosity mixture of polyamines. The 105 Resin/206 Slow Hardener has a pot life of 30-40 minutes at 70°F. It is normally used when extended time is needed for large coating and bonding applications. It is especially well suited to working in warmer climates. Partial cure time is 9 hours at 70°F. Order by size and hardener below.

Note: Pumps sold separately. Ratio pumps consists of three pumps to cover 301 and 303 A, B, & C kits. Resin pump fits either gallons or quarts.
   
California Prop 65 Warning Symbol

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Reviews

I have liked this stuff for a long time.

James S Verified Purchase

West System Epoxy Kit A-1 Fast

October 22, 2024

Kenneth L Verified Purchase

West System Epoxy Kit A-2 Slow

September 23, 2024

Great product!

Bob M Verified Purchase

West System Epoxy Kit A-1 Fast

July 16, 2024

Good consistent results if a bit pricey

Grueninger A Verified Purchase

West System Epoxy Kit B-2 Slow

May 21, 2024

Parfait

Gilles C Verified Purchase

West System Epoxy Kit A-2 Slow

March 8, 2024

Gary D Verified Purchase

West System Epoxy Kit B-2 Slow

November 18, 2023

Best kit on the market for ease of use.

Bruce W Verified Purchase

West System Epoxy Kit A-1 Fast

March 14, 2023

Both cans were bashed in from inadequate packing. AS wouldn’t replace unless it was leaking. Really disappointing

Don E Verified Purchase

West System Epoxy Kit B-2 Slow

October 14, 2022

Works great, but I found it difficult to measure out proportional amounts of Resin & Hardener

Thomas E Verified Purchase

West System Epoxy Kit A-2 Slow

July 12, 2022

Product as ordered

Serge B Verified Purchase

West System Epoxy Kit A-1 Fast

April 19, 2022

Q&A

Please note, Aircraft Spruce's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

Q: Do the West Systems Epoxy kits work well with fabrics?

Yes and no. This product is ideal for fiberglass applications. It is not intended for use with Dacron or Poly-Fiber fabrics.

Q: West System recommend for bonding that you wet up wood with 2 part epoxy, but that you then add fillers to thicken the epoxy before applying a thicker gap filling coat and clamping. For aircraft use, are fillers recommended or just the 2 part epoxy?

This will all depend on what the builders manual recommends. You can use a filler with the West System kits, but you will need to check where this will apply to your aircraft application.

Q: Is there a expiration date on the hardner or resin? The hardner I have on my shelf is a rusty brown color.

There is a 2-year shelf life, the hardener should still be reactive with the resin.

View in Catalog

View Image View in Catalog