LOBSTER MOUNTS

The "Shrimp" Series of mounts provide an economical solution for mounting mobile electronics. This basic system provides a minimal extension, and utilizes a tri-wing finger knob for locking and positioning. Our off-centered 1-1/4 inch ball-base (patent pending) provides adaptability that cannot be matched. The Shrimp mount extends as little as 2-1/2 inches from the mounting surface and can extend to about 5 inches. The "Shrimp" was designed to support devices up to 3 lbs, and is available with bolt-on, MC/ATV, and Suction bases. Universal MC-ATV Clamp Base only! For an additional anchor point we offer this universal rail-clamping base, designed to fit square or round tubing from 3/4 inch to 1-1/2 inch diameter (by adding a 1/4-20 x 3” bolt, this base will fit up to 1-3/4 tube). This rugged base is made from extruded aluminum, an aluminum ball, and includes stainless steel hardware. Weight - Unit 0.5 lbs. P/N 11-04709 $24.85 Universal Cradle The Cradle comes with four grip fingers and one stop finger, which are capable of being positioned in any of the eight slots on the body. Rubber pads for the grip fingers and stainless steel hardware are provided. In the short direction, the grip fingers are adjustable from 1-1/2” to 3-1/4”, and in the long direction, the grip fingers adjust from 4-1/2” to 5-1/2”. For longer devices, the fingers on top could be left off, allowing the device to overhang the cradle base. This product, like our other products is produced for use in aviation and marine environments where being compass compatible and corrosion resistant are important. P/N 11-04710 $16.75 Shrimp Series Bolt-On with Camera Top A removable 1/4-20 camera stud, universal mounting ball-base and mounting flange, lanyard loop; accommodates the AMPS bolt up pattern (AMPS is a 1-1/2” by 1-3/16” screw hole pattern used in many portable electronic products). Aluminum alloy and reinforced composite parts with stainless steel hardware. P/N 11-04711 $16.75 Shrimp Series MC/ATV Clamp with Camera Top Same as our Bolt-On model, while adding a universal rail-clamping base, designed to fit square or round tubing from 3/4 inch to 1-1/4 inch diameter (by adding a 1/4-20 x 3” bolt, this base will fit up to 1-3/4” tube). This rugged base is made from extruded aluminum, an aluminum ball, and includes stainless steel hardware. P/N 11-04713 $31.50 Shrimp Series Bolt-On + Cradle Universal mounting ball-base and mounting flange, lanyard loop, along with our cradle for hand-held devices. The Cradle (UN-198) comes with four grip fingers and one stop finger, which are capable of being positioned in any of the eight slots on the body. Rubber pads for the grip fingers and stainless steel hardware are provided. In the short direction, the grip fingers are adjustable from 1-1/2” to 3-1/4”, and in the long direction, the grip fingers adjust from 4-1/2” to 5-1/2”. For larger devices, the finger may be left out at the top allowing the device to overhang the cradle base. Like our other products, the SH-259 is produced for use in aviation and marine environments where being compass compatible and corrosion resistant are important. P/N 11-04715 $27.50 Shrimp Series Suction + Cradle Our Suction Base attachment ball is capable of being tilted for extra versatility in positioning your device. The Cradle (UN-198) comes with four grip fingers and one stop finger, which are capable of being positioned in any of the eight slots on the body. Rubber pads for the grip fingers and stainless steel hardware are provided. In the short direction, the grip fingers are adjustable from 1-1/2” to 3-1/4”, and in the long direction, the grip fingers adjust from 4-1/2” to 5-1/2”. For larger devices, the finger may be left out at the top allowing the device to overhang the cradle base. This mount, like our other products is produced for use in aviation and marine environments where being compass compatible and corrosion resistant are important. P/N 11-04716 $38.90 Shrimp Series MC/ATV + Cradle A universal rail-clamping base, designed to fit square or round tubing from 3/4 inch to 1-1/4 inch diameter. This rugged base is made from extruded aluminum, an aluminum ball, and includes stainless steel hardware. The Cradle comes with four grip fingers and one stop finger, which are capable of being positioned in any of the eight slots on the body. Rubber pads for the grip fingers and stainless steel hardware are provided. In the short direction, the grip fingers are adjustable from 1-1/2” to 3-1/4”, and in the long direction, the grip fingers adjust from 4-1/2” to 5-1/2”. For larger devices, the finger may be left out at the top allowing the device to overhang the cradle base. Like our other products, its produced for use in aviation and marine environments where being compass compatible and corrosion resistant are important. P/N 11-04717 $38.90   UN-327 SUCTION BASE Suction Base Only, If you are already using a Bolt-On or MC/ATV base, this allows you to easily transfer your device to your car or any place with a smooth surface. The Suction Base attachment ball is capable of being titled for extra versatility in positioning your device. This base, like the other products is produced for use in aviation and marine environments where being compass compatible and corrosion resistant are import. P/N 11-06616 $24.95   SH-334 SHRIMP SUCTION MOUNT WITH CAMERA TOP Our Suction Base attachment ball is capable of being tilted for extra versatility in positioning your device. The Camera Top (UN-310) has a removable 1/4-20 camera stud. It also features a mounting surface with holes and slots, which accommodate the AMPS standard (1.496" x 1.181") pattern for direct attachment to numerous electronic devices. This base, like our other products, is produced for use in aviation and marine environments where being compass compatible and corrosion resistant are important. P/N 11-06617 $31.50   UN-303 ROLL BAR CLAMP Base only! For your ATV, golf cart steering column or other applicable with 1-1/2" to 2-1/2" tubing. This rugged base is made from aluminum extrusion, an aluminum ball, and zinc plated steel hardware. Note that this is not compass friendly. P/N 11-06618 $26.75   UN-310 CAMERA TOP Camera Mounting surface that can also be used for mounting other devices. If you are already using a Universal Cradle (UN-198), this allows you to easily use your mounting system for other purposes. The holes and slots in the flange accommodate the AMPS standard pattern as well as several size u-bolts. This base, like our other products is produced for use in aviation and marine environments where being compass-compatible and corrosion resistant are important. P/N 11-06615 $9.50